Saab 92 Forum : Saab92x.com / Mod guides and FAQ's on other boards

iota · 2005-06-28 22:00:05

The boys over at NASIOC have a great thread with links to info about all of the mods for the WRX.

http://forums.nasioc.com/forums/showthread.php?t=533787

Also, be sure to check out ScoobyMods:

http://www.scoobymods.com

Thanks to EASE27 for the NASIOC tip! Does anyone else have any good links?

Saab92X.com · Remove Advertisements

Anand · 2005-06-29 00:24:21

Repost!

https://www.saab92x.com/viewtopic.php?id=741

big_smile

ease27 · 2005-06-29 00:30:56

POst reply.. my bad I did that earlier today, signed off and when I came back I guess Iota had gotten my email. big_smile

antrey · 2005-08-27 00:07:34

Check out: http://9-2x.dynamic-dyno.com/RemovingUp-pipeCat.html to download a video I made outlining the steps to remove and install a gutted up-pipe.

saabturbo · 2009-09-26 22:36:39

Last edited by saabturbo (2011-08-31 12:50:02)

Ben · 2009-09-26 22:38:22

Woah.

eurospek · 2009-09-26 23:01:42

MotoRaider · 2009-09-28 00:40:08

Thanks for coverting to links! embeer

BoxerWhoosh · 2009-10-22 23:31:27

eurospek wrote:

good work.

saabturbo · 2010-08-28 23:26:21

Nuts and bolts

Common to WRX or STI regardless of year

Front O2 sensor plug = M18 x 1.5

Up-pipe EGT plug = M12 x 1.25

ECU cover plate = M6 x 1.0

Intake manifold to TGV risers = M6 x 1.00 x 40

Sway bar bolts (bushings and endlinks), strut tops, ram intake duct, the spare tire hold-down, plastic splash shield, and jacking plate = M8 x 1.25

Exhaust bolts and a bunch of other stuff under the hood (green brackets for fuel rail, radiator mount) = M10 x 1.25

EGT bung, lug nuts, shift knob and rear subframe bolt = M12 x 1.25

Gallery threading on the block for oil pressure/temp sensors = M18 x 1.5

Oil drain bolt = M20 x 1.5

Uppipe stud: automotive stud, M10 x 1.25 by 41mm

The female fitting on the clutch line is M10x1.00

The banjos on the brake calipers are also M10x1.00

The banjo on the turbo for the oil feed line is M10X1.5

Top-mount intercooler mounting bolts are 8X1.25

Rear seat upper part (3 of them) are 10x1.25

Rear seat lower part (2 of them) are 8x1.25

Front fender attachment inside the engine bay is M6 x 1.0 x 10

Breather lines attaching to TMIC (3) are M6 x 1.0 x 10

Tow hitch bolt are M14 x 1.5

Model Year or Make-Specific

2002-2005 WRX: Caliper bracket to HUB bolts are M12 x 1.25 x 30 (Property class 6.6)

NOTES

If you can find it, grade 8 hardware is the way to go, especially high torque spec ones.

Bigger bolts/plugs such as M18 x 1.5 can be found at many automotive parts stores as oil drain bolts either with the oil change supplies or behind the counter.

Last edited by saabturbo (2011-08-19 22:06:45)

#1 2005-06-28 22:00:05

Mod guides and FAQ's on other boards

Remove Advertisements Advertisement

#2 2005-06-29 00:24:21

Re: Mod guides and FAQ's on other boards

#3 2005-06-29 00:30:56

Re: Mod guides and FAQ's on other boards

#4 2005-08-27 00:07:34

Re: Mod guides and FAQ's on other boards

#5 2009-09-26 22:36:39

Re: Mod guides and FAQ's on other boards

#6 2009-09-26 22:38:22

Re: Mod guides and FAQ's on other boards

#7 2009-09-26 23:01:42

Re: Mod guides and FAQ's on other boards

#8 2009-09-28 00:40:08

Re: Mod guides and FAQ's on other boards

#9 2009-10-22 23:31:27

Re: Mod guides and FAQ's on other boards

eurospek wrote:

#10 2010-08-28 23:26:21

Re: Mod guides and FAQ's on other boards

Board footer